Version 3.0Operating InstructionsjetStamp 790Mobile electronic hand stampwith changeable accumulatorsand flexible selection of imprints
10Stored imprintsP: 01SENT 21. JAN 2009CLOCK NO/TXT NEXT MODEP: 02SENT 21. 01. 2009CLOCK NO/TXT NEXT MODEP: 03SENT 2009 - 01 - 21CLOC
11P: 15SENT21. JAN 2009 14 : 47CLOCK NO/TXT NEXT MODEP: 16SENT21. 01. 2009 14 : 47CLOCK NO/TXT NEXT MODEIImprints P : 15 ... P : 19
12Customer - specific imprintsP : 26 ... P : 29--------------------------------------NO/TXT NEXT MODEImprints P : 26 ... P : 29 = customer - s
13Setting time and dateTo set the time and date, an impression must first be selected that containsthe date, or date and time as appropriate.First
14Different settings of the NumbererThe numbering device is used for the successive numbering of forms.Numbering can be increasing or decreasing.
15Numberer - setting starting point or figures :Press [ NEXT ] if necessary repeatedly, until the display shows“INPUT - NUMBERER 1” “INPUT - N
16Setting pre-textsThere are 12 different standard pre-texts stored in the stamp for each language. The set pre-text (or blanks if pre-text is swit
17StampingStamping will be triggered by pressing the red trigger, which is located in the grip.Depending on the selected imprint, the imprint will hav
18Changing the ink cartridgeRemoving a used ink cartridge:Press [ MODE ] , if necessary repeatedly, untilthe menu item “INKJET” appea
19Dirt and dried up ink at the holderof the ink cartridge can be removedwith a soft cleaning cloth moistenedin spirit (see figure1)Insert the new ink
2© 2003 Ernst Reiner GmbH & Co. KGAll rights reserved. Translations, reprints, or any other form of reproduction of this manual, even in part a
20Setup moduleThe Setup module contains the following two main menues:SETTINGS: Enables comprehensive, extensive changes to settings to be carried ou
21Description of the Setup modulePress repeatedly if necessary until ‘SETUP’is displayed in the menu line(Enter password if required)SETUPMODEFir
22continuation see next pageActivation of an imprint (01 ... 29)Add imprint(s) to favourites listOnly imprints marked 'ON' are shown wh
23Exchange lines (OFF / ON)ON = top and bottom lines of imprint exchangedLeading zeros of NumbererON = leading zeros displayed and printedOFF = lea
24BLOCK IMPRINTPASSW SETUPPASSW CLOCKPASSW NO/TXTPASSW PRINTVARYVARYVARYVARYVARYNEXTNEXTNEXTNEXTNEXTsee page 20STAMP PICTUREPrint blockade setti
25Troubleshooting Display Cause RecommendationIMPRINT Time allowed by ‘Block Imprint’ Press [ QUIT ] :BLOCKED has expired, after that trigger j
26Safety guidelines for accumulatorsBatteries are likely to deteriorate.For this reason a lifetime of more than 6 months cannot be guaranteed• Onl
27Guidelines on commissing and operating accumulators• The charging of accumulators is electronically controlled. This ensures that the accumulator
28Technical dataStamping time approx. 0,7 secondsStamping cycle > 2 secondsPrint capacity per ink cartridge approx. 300.000 charactersStand b
29Tested safetyjetStamp is manufactured to the safety standards IEC / EN 60950 - 1MarkingjetStamp complies with EC directives2004 / 108 / EG
Control elements ...Commissioning ...
30
Ernst Reiner GmbH & Co. KGBaumannstr. 16D - 78120 FurtwangenTelephone + 49 7723 6570Fax + 49 7723 657200E - Mail [email protected] www.
41 = Charging station with mains unit2 = Socket for power supply (reverse side)3 = Green charge-indicator lamp4 = Trigger5 = Display6 = Buttons7 = Lo
5CommissioningUnpack equipmentConnect plug power adaptor provided to base station and connectto mains voltageNote: Only use original REINER component
6Place jetStamp in the charging station and load accumulatorsObserve the following guidelines:•Hook jetStamp to the notch (9) and place it in the c
7Insert ink cartridgeWhen necessary press repeatedly [ MODE ] until menu item "INKJET" is displayed on the lower display linePress
8Display zones and button funcitons P : 25 R : 01 / 01SENT 0000000021. JAN 2009 14 : 47CLOCK NO/TXT NEXT MODEThe display is divided into
9Imprint selectionA total of 25 different standard imprints are stored (see pages 10 / 11)These contain the individual printing fields 'Pre-te
Comments to this Manuals