Reiner jetStamp 792 Operations Instructions Page 1

Operating instructionsjetStamp 792Electronic hand stampwith Flexible Impression SelectionVersion 2.2

10P: 15RECUD10. SEP 2006 14 : 47CLOCK NO/TXT NEXT MODEP: 16RECUD10. 09. 2006 14 : 47CLOCK NO/TXT NEXT MODEImpressions P : 15 ... P : 19

11Customer-specific impressionsP : 26 ... P : 29--------------------------------------NO/TXT NEXT MODEImpressions P : 26 ... P : 29 = customer

12Setting time and dateTo set the time and date, an impression must first be selected that containsthe date, or date and time as appropriate.First

13Setting numbering device or figuresThe numbering device is used for the successive numbering of forms.Numbering can be increasing or decreasing.

14Numbering device - setting starting point or figures :Press [ NEXT ] if necessary repeatedly, until the display shows“INPUT - NUMBERER 1” “I

15Setting pre-textsThere are 12 different standard pre-texts stored in the stamp for each language. The set pre-text (or blanks if pre-text is switch

16StampingStamping will be triggered by pressing the red trigger, which is located in the grip.Depending on the impression selected, the impression wi

17Changing the ink cartridgeRemoving a used ink cartridge:Press [ MODE ] , if necessary repeatedly, untilthe menu item “INKJET” appearsPr

18Dirt and dried up ink at the holderof the ink cartridge can be removedwith a soft cleaning cloth moistenedin spirit (see figure 2)Insert the new in

19Setup moduleThe Setup module contains the following two main menus:SETTINGS: Enables comprehensive, extensive changes to settings to be carried out

2© 2003 Ernst Reiner GmbH & Co. KGAll rights reserved. Translations, reprints, or any other form of reproduction of this manual, even in part a

20Description of the Setup modulePress, repeatedly if necessary(Enter password if required)SETTINGSUPDATEFIRMWARE ALLFIRMWARE PARTSTAMP PICTUREPRE

21STAMP PICTURESET STAMP PICTSETTINGSActivate impression (01 ... 29) Add impression(s) to favourites listOnly impressions marked 'ON'

22CHANGE LINEPRE CHAR 0 Exchange lines (OFF / ON)ON = top and bottom lines of impression exchangedLeading zeros on numbering deviceON = leading z

23Ink cartridge settings1 = standard ink cartridge 2 = ink cartridge with quick-drying inkrinsing every 8 seconds 3 = ink cartridge with quick-dryi

24Troubleshooting Display Cause RecommendationIMPRINT Time allowed by ‘Block Imprint’ Press [ QUIT ] :BLOCKED has expired, disappears trigger j

25Sales and Technical ServiceFor further information, please contact one of the following:Sales - Germany:REINER Customer Service in FurtwangenTel

26Technical dataTested safetyjetStamp is manufactured to the safety standards IEC 950, EN 60950 and VDE 0805 .MarkingsjetStamp complies with

790 103 - 021 b 04 / 07Ernst REINER GmbH & Co. KGPostfach 1351D - 78115 FurtwangenTelephone + 49 7723 6570Fax + 49 7723 657200E-Mail rei

Table of contentsSafety instructions ...Control elements ...

4Safety instructionsOn this page, you will find safety instructions that you must always observe when handling and working with your Electronic Hand

1 = Base station 2 = jack bush for power supply3 = Trigger4 = Display5 = Buttons6 = Locking rail for ink cartridge7 = Ink cartridge8 = Locating tab9 =

Commissioning Unpack the stamp, connect the mains unit to jetStamp 792, plug in the mains unit and switch on the power supply.Note: Use only original

7Display zones and button funcitons P : 25 R : 01 / 01SENT 0000000024. APR 2006 14 : 47CLOCK NO/TXT NEXT MODEThe display is divided into

8Impression selectionA total of 25 different standard impressions are stored (see pages 9 / 10).These contain the individual printing fields &apos

Stored impressionsP: 01RECUD 24. SEP 2006CLOCK NO/TXT NEXT MODEP: 02RECUD 24. 09. 2006CLOCK NO/TXT NEXT MODEP: 03RECUD 2006 - 09